Showing 61–72 of 113 results

IC NE555 ST

7.00
Features • Timing from microseconds to hours • Astable or monostable operation • Adjustable duty cycle • TTL compatible output can source or sink up to 200mA • Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) • Halogen- and Antimony-Free. “Green” Device (Note 3) • For automotive applications requiring specific change control (i.e. parts qualified to AEC-Q100/101/200, PPAP capable

IC PIC16F72 MC

140.00
  • 25mA sink/source per I/O, Capture/Compare

IC PIC16F73 MC

98.00
The PIC16F73 is a 28/40-Pin 8-Bit CMOS FLASH Microcontrollers . The following are the features:- • Timer0: 8-bit timer/counter with 8-bit prescaler • Timer1: 16-bit timer/counter with prescaler, can be incremented during SLEEP via external crystal/clock • Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler • Capture, Compare, PWM (CCP) module - Capture is 16-bit, max. resolution is 12.5 ns - Compare is 16-bit, max. resolution is 200 ns - PWM max. resolution is 10-bit • 8-bit, 5-channel analog-to-digital converter • Synchronous Serial Port (SSP) with SPI™ (Master/Slave) and I2C™ (Slave) • Brown-out detection circuitry for Brown-out Reset (BOR)

IC PIC16F883 MC

110.00
Features of PIC16F886 Microcontroller :-  
  • Power-Saving Sleep mode
  • Power-on Reset (POR)
  • Selectable Brown-out Reset (BOR) voltage
  • Extended Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation
  • In-Circuit Serial Programming™ (ICSP™) via two pins
  • In-Circuit Debug (ICD) via two pins
  • High-endurance Flash/EEPROM cell:
  • 100,000 erase/write cycle enhanced Flash program memory, typical
  • 1,000,000 erase/write cycle data EEPROM memory, typical
  • Data EEPROM retention > 40 years
  • Self-reprogrammable under software control
  • Programmable code protection
  Peripheral Features of PIC16F886 Microcontroller:-  
  • 1 input only pin
  • 25 I/O
  • High sink/source current 25 mA
  • Interrupt-on-pin change option
  Timers:-  
  • TMR0: 8-bit timer/counter with 8-bit prescaler
  • TMR1 enhanced: 16-bit timer/counter with prescaler, External Gate Input mode and dedicated low-power 32 kHz oscillator
  • TMR2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler
  • Capture/Compare/PWM (CCP) module
  • Enhanced Capture/Compare/PWM (ECCP) module with auto-shutdown and PWM steering
  • Master Synchronous Serial Port (MSSP) module SPI™ mode, I2C™ mode with address mask capability
  • Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) module:
  • Supports RS-485, RS-232 and LIN compatibility
  • Auto-Baud Detect
  • Auto-wake-up on Start bit
  • Ultra Low-Power Wake-up (ULPWU)
  Analog Features of PIC16F886 Microcontroller:-  
  • 10-bit 11 channel Analog-to-Digital (A/D) Converter
  • 2 Analog Comparator modules with:
  • Programmable on-chip Voltage Reference (CVREF) module (% of VDD)
  • Fixed 0.6 Vref
  • Comparator inputs and outputs externally accessible
  • SR Latch mode

IC TLP521

13.00
      • Collector−emitter voltage: 55 V (min) • Current transfer ratio: 50% (min) Rank GB: 100% (min) • Isolation voltage: 2500 Vrms (min) • UL recognized made in Japan: UL1577, file No. E67349 made in Thailand: UL1577, file No. E152349

      Benefits

      • Standard pinout allows for drop in replacement
      • High-current carrying capability package
      • Industry standard qualification level
      • High performance in low frequency applications
      • Increased power density
      • Provides designers flexibility in selecting the most optimal device for their application

IC TOP253PN

75.00
    1. Multi-mode operation maximizes efficiency at all loads
    2. Low height is ideal for adapters where space is limited
    3. Line under-voltage detection prevents turn-OFF glitches
    4. Line over-voltage shutdown extends line surge limit
    5. Accurate programmable current limit
    6. Heat sink is connected to source for low EMI
    7. Fully integrated soft-start for minimum start-up stress

IC TOP253PN

73.00
Arduino Uno Rev3 Code: A000066 / Barcode: 7630049200050 Nunc per mollis pot enti amet imperdiet blandit dis eu sociosqu accumsan

ICs current sensor AC57581/CB-050U

349.00
  • Primary sampled current (Ip) of 50A
  • Sensitivity is 60mV/A
  • Current directionality is unidirectional
  • Automotive grade AEC Q-100 qualified
  • Ultra low power loss, 100µohm internal conductor resistance
  • Single supply operation from 3V to 5.5V
  • 120KHz typical bandwidth
  • 3µs output rise time in response to step input current
  • Output voltage proportional to AC or DC currents
  • Operating temperature range from -40°C to 85°C

ICs current sensor ACS758 brand new and Original ACS758LCB-100B-PFF-T linear Hall Effect Sensor 5-Pin CB PFF 100A Bidirectional

320.00
  • Primary sampled current (Ip) of ±50A
  • Sensitivity is 40mV/A
  • Current directionality is bidirectional
  • Automotive grade AEC Q-100 qualified
  • Ultra low power loss, 100µohm internal conductor resistance
  • Single supply operation from 3V to 5.5V
  • 120KHz typical bandwidth
  • 3µs output rise time in response to step input current
  • Output voltage proportional to AC or DC currents
  • Operating temperature range from -40°C to 85°C

Applications

Sensing & Instrumentation, Motor Drive & Control, Power Management, Automotive

ICs current sensor ACS758 brand new and Original ACS758LCB-100u-PFF-T linear Hall Effect Sensor 5-Pin CB PFF 100u Bidirectional

390.00
Allegro ACS758 family of current sensor ICs provides economical and precise solutions for AC or DC current sensing. Typical applications include motor control, load detection and management, power supply and DC-to-DC converter control, inverter control, and overcurrent fault detection. The device consists of a precision, low-offset linear Hall circuit with a copper conduction path located near the die. Applied current flowing through this copper conduction path generates a magnetic field which the Hall IC converts into a proportional voltage. Device accuracy is optimized through the close proximity of the magnetic signal to the Hall transducer. A precise, proportional output voltage is provided by the low-offset, chopper-stabilized BiCMOS Hall IC, which is programmed for accuracy at the factory. High-level immunity to current conductor dV/dt and stray electric fields, offered by Allegro proprietary integrated shield technology, guarantees low output voltage ripple and low offset drift in high-side, high-voltage applications. The output of the device has a positive slope (>VCC / 2) when an increasing current flows through the primary copper conduction path (from terminal 4 to terminal 5), which is the path used for current sampling. The internal resistance of this conductive path is 100 µΩ typical, providing low power loss. The thickness of the copper conductor allows survival of the device at high overcurrent conditions. The terminals of the conductive path are electrically isolated from the signal leads (pins 1 through 3). This allows the ACS758 family of sensor ICs to be used in applications requiring electrical isolation without the use of opto-isolators or other costly isolation techniques. The device is fully calibrated prior to shipment from the factory. The ACS758 family is lead (Pb) free. All leads are plated with 100% matte tin, and there is no Pb inside the package. The heavy gauge leadframe is made of oxygen-free copper.
  • Industry-leading noise performance through proprietary amplifier and filter design techniques
  • Integrated shield greatly reduces capacitive coupling from current conductor to die due to high dV/dt signals, and prevents offset drift in high-side, high-voltage applications
  • Total output error improvement through gain and offset trim over temperature
  • Small package size, with easy mounting capability
  • Monolithic Hall IC for high reliability
  • Ultralow power loss: 100 µΩ internal conductor resistance
  • Galvanic isolation allows use in economical, high-side current sensing in high-voltage systems
  • AEC-Q100 qualified
  • 3.0 to 5.5 V, single supply operation
  • 120 kHz typical bandwidth
  • 3 µs output rise time in response to step input current
  • Output voltage proportional to AC or DC currents
  • Factory-trimmed for accuracy
  • Extremely stable output offset voltage
  • Nearly zero magnetic hysteresis

ICs current sensor ACS758LCB-050B-PFF-T

320.00
  • Primary sampled current (Ip) of ±50A
  • Sensitivity is 40mV/A
  • Current directionality is bidirectional
  • Automotive grade AEC Q-100 qualified
  • Ultra low power loss, 100µohm internal conductor resistance
  • Single supply operation from 3V to 5.5V
  • 120KHz typical bandwidth
  • 3µs output rise time in response to step input current
  • Output voltage proportional to AC or DC currents
  • Operating temperature range from -40°C to 85°C

IR2153 IC – Self Oscillating Half Bridge Driver IC

96.50
  • Integrated 600V half-bridge gate driver
  • 15.6V Zener clamp on Vcc
  • True micropower start up
  • Tighter initial deadtime control
  • Low-temperature coefficient deadtime