Resistors
Connectors
Capacitors
Wires and Connectors
Shop
ESP Prog – CP2102 Based ESP32
- Size: 50mmx30mm
- USB-C Type Interface: you can connect a USB in any direction. Use USB-A to USB-C Cable.
- LEDs for Power, RX, TX
- Switch for Reset and Boot
- Both 3.3V and 5V are available on the O/P connector
- All signals on a standard 2.54mm Pitch Header (Header will come along with the board (unsoldered))
- USB-C Type Interface: A USB can be connected in any direction. Use a USB-A to USB-C cable.
- LEDs for Power, RX, TX
- Switch for Reset and Boot
- Both 3.3V and 5V are available on the O/P connector
- All signals on a standard 2.54mm Pitch Header (Header will come along with the board (unsoldered))
- Compact size: 50mmx30mm
- 3.3V DC (100mA Max.)
- TXD
- RXD
- GND
- Reset/RTS
- Boot/DTR
- GND
- 5V DC (500mA Max.)
ESP32 Capacitive Touch Sensor Pins with Arduino IDEDS
ESP32 is designed for mobile, wearable electronics, and Internet-of-Things (IoT) applications. It features all the
state-of-the-art characteristics of low-power chips, including fine-grained clock gating, multiple power modes,
and dynamic power scaling. For instance, in a low-power IoT sensor hub application scenario, ESP32 is woken
up periodically only when a specified condition is detected. Low-duty cycle is used to minimize the amount of
energy that the chip expends. The output of the power amplifier is also adjustable, thus contributing to an
optimal trade-off between communication range, data rate and power consumption.
ESP32-CAM WiFi Bluetooth Camera Module Development Board ESP32 With Camera Module OV2640 2MP
Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
Low-power dual-core 32-bit CPU for application processors
Up to 240MHz, up to 600 DMIPS
Built-in 520 KB SRAM, external 4M PSRAM
Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
Support for images WiFI upload
Support TF card
Support multiple sleep modes
Embedded Lwip and FreeRTOS
Support STA/AP/STA+AP working mode
ESP8266 ESP-01 WiFi Module
Features:
- 802.11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLLs, regulators, DCXO and power management units
- +19.5dBm output power in 802.11b mode
- Power down leakage current of <10uA
- 1MB Flash Memory
- Integrated low power 32-bit CPU could be used as application processor
- SDIO 1.1 / 2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
FAN7392 High-Current, High- & Low-Side, Gate-Drive IC
Features:-
- Floating Channel for Bootstrap Operation to +600V
- 3AJ3A Sourcing/Sinking Current Driving Capability
- Common-Mode dv/dt Noise Canceling Circuit
- 3.3V Logic Compatible Separate Logic Supply (VDD) Range from 3.3V to 20V
- Under-Voltage Lockout for vcc and VBS Cycle-by-Cycle Edge-Triggered Shutdown Logic
- Matched Propagation Delay for Both Channels
- Outputs In-phase with Input Signal
Flame Sensor infrared Receiver Ignition source detection module
-
Features :
- Indicator light: a green one for the switch, a red one for power.
- Built in a potentiometer for sensitivity control.
- Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO.
- Can detect fire or wavelength in 760 ~ 1100 nm nano within the scope of the light source.
- Detection angle about 60 degrees, the flame spectrum especially sensitive.
- The flame of the most sensitive sensors flame, the regular light is also a response, generally used for fire alarm purposes.
FUSE HOLDERS FH1
FUSE HOLDERS FH5
FUSE HOLDERS FH6
FUSE HOLDERS FH7
FUSE HOLDERS PBF4
Brand:
VITAL
Moulded Material:
Polyamide (Nylon) 66 - UL94 V0 or V2 - Glass Filled
Nominal Rating:
6.30A/250V
Mounting Style:
PCB Type
Insulation Resistance:
1000 M-ohm @ 500 Vdc"}" data-sheets-numberformat="[null,2,"@",1]">> 1000 M-ohm @ 500 Vdc
Permissible Soldering Temp:
270 C for 5 sec max
Permissible Operating Temp:
-20 C to +85 C
Contact Resistance:
10 m ohm max
Approx Weight:
2.5 gms
Terminal:
Tin plated copper alloy
Fuse Link:
5 X 20 mm
Product Specification
| Fuse Type | Panel Mount |
| Current Rating | 6.3A |
| Brand | Elcom |
| Voltage | 250V AC |
| Mounting Style | Panel Mount |
| Contact Resistance | 10 m Ohms max |
| Fuse Link Size | 5x20 mm |
| HV Breakdown Test | 2KV AC For 1 Minute |
| Panel Thickness | 5.0 mm |
| Rated Current | 6.3 Amps |
GLUN 11 mm Transparent HOT MELT 14 Glue Sticks for DIY and Craft Work
HLF DIP Cd4001be Integrated Circuit, For Power
