Resistors
Connectors
Capacitors
Wires and Connectors
Shop
Arduino UNO R3 Development Board
The Arduino Uno R3 is a open source microcontroller board based on the ATmega328 chip. This Board has 14 digital input/output pins, 6 analog input pins, Onboard 16 MHz ceramic resonator, Port for USB connection, Onboard DC power jack, An ICSP header and a microcontroller reset button. It contains everything needed to support the microcontroller. Using the board is also very easy, simply connect it to a computer with a USB cable or power it with DC adapter or battery to get started.
* Product Images are shown for illustrative purposes only and may differ from actual product.
The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2Atmega8U2 up to version R2) programmed as a USB-to-serial converter. While the Arduino UNO can be powered via the USB connection or with an external power supply, the power source is selected automatically.
External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the board's power jack. Also leads from a battery can be inserted in the Gnd and Vin pin headers of the Power connector. The board can operate on an external supply of 6 to 20 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts and the board may be unstable. If using more than 12V, the voltage regulator may overheat and damage the board. The recommended range is 5v to 12v for Arduino Uno.
Features:-
- Microcontroller: ATmega328P.
- Operating Voltage: 5V.
- Input Voltage: 7-12V.
- Digital I/O Pins: 14 (of which 6 provide PWM output).
- Analog Input Pins: 6.
- DC Current: 40mA.
- Flash Memory: 32 KB.
- SRAM: 2 KB.
- EEPROM: 1 KB.
- Clock Speed: 16 MHz.
Applications:-
- DIY project prototyping.
- Developing varied varieties of projects that require a code based control.
- Automation System development.
- Learning AVR programming.
- Entry level circuit designing.
Battery charger hybrid CATCHER BC200
BC547 NPN TO 92 General Purpose Transistor 50-Pcs
BLDC FAN Kit -04 ( BLDC ceiling fan Kit )28w 300rpm
BLDC FAN Kit-01 ( BLDC ceiling fan Kit 28W 1400RPM)
- BLDC ceiling fan Kit 28W 1400RPM
- CAN BE RUN BOTH AC POWER AND DC POWER
- DO NOT USE FAN REGULATOR
- Manufacturer : Rips
- Item model number : SM-03
- Country of Origin : India
- Included Components : Canoppy, Magnet, Remote, Controller, Coil, Controller case
- NO LOAD PROTECTION & OVERLOAD PROTECTION
- SEVEN SPEED REMOTE CONTROLLER
BR1010 1.1V 10A Single Phase Bridge Rectifier
Features:-
- Single Phase Bridge Rectifier are Higher Output Voltage, Higher Output Power and Higher Transformer Utilization Factor in Case of Single Phase Rectifier.
- It Has High Transformer Utilization Factor, It Can be Constructed with or without Transformer, Electric Current is Allowed During Both Positive and Negative Half Cycles of the Input AC Signal.
- Bridge Rectifier is Smoother than the Half Wave Rectifier.
- For Single Phase Bridge Rectifier, No Center Tap Transformer is Needed.
- Type: Single Phase
- Size: 19.6mm Length, 19.6mm Width, 7.5mm Height
- Voltage Rating: 1000V Peak Reverse, 700V RMS, 1.1V Forward
- Current Rating: 10A Forward, 200A Surge, 5uA Reverse
- Temperature Rating: −55 to 150 Deg C
- Mounting: PCB
- Thermal Resistance: 9.4 Deg C/W.
CD4017 CD4017BE 4017 Decade Counter Divider IC Pack of 5PCS
- CD4017 Decad Counter IC With 16 Pin IC Base Free The CD4017B is a 5-stage Johnson counter with 10 decoded outputs. Inputs include a CLOCK, a RESET, and a CLOCK INHIBIT signal. Schmitt trigger action in the CLOCK input circuit provides pulse shaping that allows unlimited clock input pulse rise and fall times.
- Decade counter IC - 4017
- Branded New IC'S -5PCS
