-31%
Click to enlarge
Previous product
Ultrasonic Distance Sensor Module - HC-SR04 ₹90.00
Back to products
Next product
Flame Sensor infrared Receiver Ignition source detection module ₹65.00

1 Channel 5V Relay Module without Optocoupler

₹45.00

  • Specification and Features :-

     

    • 1 channel relay board
    • Operating Voltage 5V
    • Max Current : 20mA
    • Relay Contact Current Capacity at AC250V: 10A
    • Relay Contact Current Capacity at DC5V: 10A
    • One normally closed contact and one normally open contact
    • Triode drive, increasing relay coil
    • High impedance controller pin
    • Pull-down circuit for avoidance of malfunction
    • Power supply indicator lamp
    • Control indicator lamp
    • Indicator for Relay output status
    • Can Be controlled various appliances & other Equipment With Large current.
    • Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
    • The module is compliant with international safety standards, control and load areas isolation trenches;
Add to wishlist
Categories: ,
Description

Arduino Uno Rev3
Code: A000066
/
Barcode: 7630049200050

 

Nunc per mollis pot enti amet imperdiet blandit dis eu sociosqu accumsan dap ibus ultricies tristique montes a deros adipiscing a justo. Aliquet mus a aptent ullamcorper metus accumsan. Habitasse a purus nec ipsum a urna ac ullamcorper varius metus blandit posuere.

Consectetur parturient ad imperdiet torquent dui dis eu sociosqu accumsan accumsan dapibus ultricies. Maecenas iaculis viverra tellus ridiculus a sed vestibulum dapibur.

Documentation

OSH: Schematics

Arduino Uno is open-source hardware! You can build your own board using the following files:

EAGLE FILES IN .ZIP SCHEMATICS IN .PDF BOARD SIZE IN .DXFDATASHEET IN .PDF

Tech specs


MICROCONTROLLER ATmega328P
OPERATING VOLTAGE 5V
INPUT VOLTAGE (RECOMMENDED) 7-12V
INPUT VOLTAGE (LIMIT) 6-20V
DIGITAL I/O PINS 14 (of which 6 provide PWM output)
PWM DIGITAL I/O PINS 6
ANALOG INPUT PINS 6
DC CURRENT PER I/O PIN 20 mA
DC CURRENT FOR 3.3V PIN 50 mA
FLASH MEMORY 32 KB (ATmega328P) of which 0.5 KB used by bootloader
SRAM 2 KB (ATmega328P)
EEPROM 1 KB (ATmega328P)
CLOCK SPEED 16 MHz
LED_BUILTIN 13
LENGTH 68.6 mm
WIDTH 53.4 mm
WEIGHT 25 g

Additional information
Brand

Specification

Beige, Black, Blue, Brown, Yellow
Reviews (0)

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Shipping & Delivery
eCommerce-shipping-1280x720

  • Submit an order before the cut-off time to shorten your delivery time

    When selecting the delivery method, orders of in-stock items will be shipped out either the same day or next business day depending on the cut-off time listed below. Items being transferred from other global warehouses may require additional time for delivery.

    • Same-day dispatch cut-off time is: 10:30pm
    • In stock items ordered before this time will ship out the same day the order is placed.
    • Orders received on Saturday or Sunday will be shipped the next business day.

    Backorders

    Items on backorder will be despatched when they arrive back in stock. If you place an order that has one or more items on backorder you can choose whether to have all items despatched together or to receive the items currently in stock as soon as possible.

    Options for backorders

    • Backorder allowed
      We'll despatch in-stock items immediately and place any out-of-stock items on backorder. Items on backorder will be despatched as they become available. Therefore, your order may arrive in single or multiple deliveries.
    • Deliver order complete
      If any items in your order are out of stock, we can hold your entire order until all items become available. Your order will then arrive in one delivery.

Delivery fee

Terms & Conditions

  • Dimensional weight calculations and volumetric weight calculations may apply. For products above 5kg or for products which are bulky or hazardous, please get in touch with us.
  • COD charges are separate for COD shipments.

To discuss shipping options, please contact us at 9846720907 , 9061396217 or send an email to [email protected]

Related products

-15%
Close

ESP32 Capacitive Touch Sensor Pins with Arduino IDEDS

,
₹410.00
ESP32 is designed for mobile, wearable electronics, and Internet-of-Things (IoT) applications. It features all the state-of-the-art characteristics of low-power chips, including fine-grained clock gating, multiple power modes, and dynamic power scaling. For instance, in a low-power IoT sensor hub application scenario, ESP32 is woken up periodically only when a specified condition is detected. Low-duty cycle is used to minimize the amount of energy that the chip expends. The output of the power amplifier is also adjustable, thus contributing to an optimal trade-off between communication range, data rate and power consumption.
Add to wishlist
Add to cart
Quick view
-31%
Close

ESP Prog – CP2102 Based ESP32

,
₹399.00
  • Size: 50mmx30mm
  • USB-C Type Interface: you can connect a USB in any direction. Use USB-A to USB-C Cable.
  • LEDs for Power, RX, TX
  • Switch for Reset and Boot
  • Both 3.3V and 5V are available on the O/P connector
  • All signals on a standard 2.54mm Pitch Header (Header will come along with the board (unsoldered))
  • USB-C Type Interface: A USB can be connected in any direction. Use a USB-A to USB-C cable.
  • LEDs for Power, RX, TX
  • Switch for Reset and Boot
  • Both 3.3V and 5V are available on the O/P connector
  • All signals on a standard 2.54mm Pitch Header (Header will come along with the board (unsoldered))
  • Compact size: 50mmx30mm
ESP Prog Pin-Out
  1. 3.3V DC (100mA Max.)
  2. TXD
  3. RXD
  4. GND
  5. Reset/RTS
  6. Boot/DTR
  7. GND
  8. 5V DC (500mA Max.)
Add to wishlist
Add to cart
Quick view
-33%
Close

1 Pole Industrial Relay PCB Relays, Model Name/Number: GU-SS-112DFS, Voltage: 12VDC

,
₹155.00
 

Product Specification

Voltage 12VDC
Current 20/30A
Number Of Poles 1 Pole
Type Industrial Relay
Mounting Quick Contact Terminal
Brand Goodsky
Model Name/Number GU-SS-112DFS
Voltage
12VDC
Current
20/30A
Number Of Poles
1 Pole
Type
Industrial Relay
Mounting
Quick Contact Terminal
Add to wishlist
Add to cart
Quick view
-18%
Close

Ultrasonic Distance Sensor Module – HC-SR04

,
₹90.00
  • Features: 
    • Sensor Type: Ultrasonic
    • Output: Digital Sensor
    • Voltage: 5VDC
    • Detection distance: 2cm-400cm (0.02M - 4.0M)
    • Static current: < 2mA
    • Level output: high-5V
    • High precision: up to 0.3cm
Add to wishlist
Add to cart
Quick view
-6%
Close

NEO-6M GPS Module

,
₹300.00
  • Features NEO-6M GPS Module:- 
    • 5Hz position update rate
    • Operating temperature range: -40 TO 85°CUART TTL socket
    • EEPROM to save configuration settings
    • Rechargeable battery for Backup
    • The cold start time of 38 s and Hot start time of 1 s
    • Supply voltage: 3.3 V
    • Configurable from 4800 Baud to 115200 Baud rates. (default 9600)
    • SuperSense ® Indoor GPS: -162 dBm tracking sensitivity
    • Support SBAS (WAAS, EGNOS, MSAS, GAGAN)
    • Separated 18X18mm GPS antenna
Add to wishlist
Add to cart
Quick view
-33%
Close

RELAY 65-12-1CE OEN

,
₹29.99
 

Features of  OEN 12 VOLT 65-12-1CE RELAY

  • Brand : OEN
  • Voltage : 230 VAC 24 VDC.
  • Maximum switching voltage : 250 VDC.
  • Low power consumption.
  • Nominal voltage :12 V.
  • Switching current max : 10 Ampere
  • Nominal Coil Power: 0.36W (approx)
  • Operating Power: 0.23W  (approx)
  • Dust proof.
  • Contact material : Silver alloy.
  • Working temperature: -45 degree C. To 55 degree C.%
Add to wishlist
Add to cart
Quick view
-19%
Close

DIODE RHR30120FSC

,
₹72.99
• Hyperfast Recovery trr = 85 ns (@ IF = 30 A) • Max Forward Voltage, VF = 3.2 V (@ TC = 25°C) • 1200 V Reverse Voltage and High Reliability • Avalanche Energy Rated • RoHS Compliant Switching Power Supplies • Power Switching Circuits • General Purpose
Add to wishlist
Add to cart
Quick view
-7%New
Close

5AMP CURRENT TRANSFORMER, 1:1200, Pcb Mount -(with Casing) (CT 5A/1200T SHA)

,
₹68.00

Product Description

  • Designed and developed as per European Standards IEC : 62053-21 / IS: 13779 , IEC : 60044-1 Part-1.
  • Ideal for Electronic Safety Control Gear design ,
  • Overload Sensing , Furnace Temperature Control ,
  • Motor Speed Control , Instrument Transformer ,
  • Energy Metering ,
  • Power Quality Monitoring.
  • Home Automation Devices
  • Earth Leakage Circuit Braker CT ( ELCB CT )
  • Residual Current Circuit Braker CT ( RCCB CT )
  • Ground Fault Interruptor CT ( GFI CT )
  • Variants available in Self Wire (Flying Leads) or PCB Mounting Type CT.

Product Image

Shah 2 AMP CURRENT TRANSFORMER, 1:550, Pcb Mount -(with Casing)
Add to wishlist
Add to cart
Quick view