Resistors
Connectors
Capacitors
Wires and Connectors
DEVELOPMENT BOARDS & PROTOTYPING
DRIVER CARD, FOR EXIDE ,V GUARD,AMARON, WHIRLPOOL,KEVIN 850/650/1050
DSP PURE SINEWAVE INVERTER BOARD BULL EG-200 1000W (Suitable for LUMINUS, EXIDE, MICROTECH inverters)
*DSP BASED 32BIT MICRO CONTROLLER
*ECONOMIC SERIES WITH MORE PROTECTION
*SHUNT RESISTER IMPROVES SURGE CURRENT
*COMPATABLE FOR LITHIUM IRON BATTERY
*INTRODUCING USER DEFINED CHARGER MODE CALIBRATION
*16X2 LCD WITH 6 LED LCD BACKLIGHT AUTO OFF IMPROVES LCD LIFE
*HEAVY MOSFET OPTO COUPLER DRIVER
*COMPACT IN SIZE (Suitable for LUMINUS, EXIDE, MICROTECH inverters)
ESP Prog – CP2102 Based ESP32
- Size: 50mmx30mm
- USB-C Type Interface: you can connect a USB in any direction. Use USB-A to USB-C Cable.
- LEDs for Power, RX, TX
- Switch for Reset and Boot
- Both 3.3V and 5V are available on the O/P connector
- All signals on a standard 2.54mm Pitch Header (Header will come along with the board (unsoldered))
- USB-C Type Interface: A USB can be connected in any direction. Use a USB-A to USB-C cable.
- LEDs for Power, RX, TX
- Switch for Reset and Boot
- Both 3.3V and 5V are available on the O/P connector
- All signals on a standard 2.54mm Pitch Header (Header will come along with the board (unsoldered))
- Compact size: 50mmx30mm
- 3.3V DC (100mA Max.)
- TXD
- RXD
- GND
- Reset/RTS
- Boot/DTR
- GND
- 5V DC (500mA Max.)
ESP32 Capacitive Touch Sensor Pins with Arduino IDEDS
ESP32 is designed for mobile, wearable electronics, and Internet-of-Things (IoT) applications. It features all the
state-of-the-art characteristics of low-power chips, including fine-grained clock gating, multiple power modes,
and dynamic power scaling. For instance, in a low-power IoT sensor hub application scenario, ESP32 is woken
up periodically only when a specified condition is detected. Low-duty cycle is used to minimize the amount of
energy that the chip expends. The output of the power amplifier is also adjustable, thus contributing to an
optimal trade-off between communication range, data rate and power consumption.
ESP32-CAM WiFi Bluetooth Camera Module Development Board ESP32 With Camera Module OV2640 2MP
Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
Low-power dual-core 32-bit CPU for application processors
Up to 240MHz, up to 600 DMIPS
Built-in 520 KB SRAM, external 4M PSRAM
Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
Support for images WiFI upload
Support TF card
Support multiple sleep modes
Embedded Lwip and FreeRTOS
Support STA/AP/STA+AP working mode
ESP8266 ESP-01 WiFi Module
Features:
- 802.11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLLs, regulators, DCXO and power management units
- +19.5dBm output power in 802.11b mode
- Power down leakage current of <10uA
- 1MB Flash Memory
- Integrated low power 32-bit CPU could be used as application processor
- SDIO 1.1 / 2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
Flame Sensor infrared Receiver Ignition source detection module
-
Features :
- Indicator light: a green one for the switch, a red one for power.
- Built in a potentiometer for sensitivity control.
- Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO.
- Can detect fire or wavelength in 760 ~ 1100 nm nano within the scope of the light source.
- Detection angle about 60 degrees, the flame spectrum especially sensitive.
- The flame of the most sensitive sensors flame, the regular light is also a response, generally used for fire alarm purposes.
INVERTER CONTROL CARD, FOR EXIDE ,V GUARD,AMARON, WHIRLPOOL,KEVIN
