Resistors
Connectors
Capacitors
Wires and Connectors
Passive Components
A passive component is an electronic component which can only receive energy, which it can either dissipate, absorb or store it in an electric field or a magnetic field.
1 Channel 5V Relay Module without Optocoupler
- Specification and Features :-
- 1 channel relay board
- Operating Voltage 5V
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for avoidance of malfunction
- Power supply indicator lamp
- Control indicator lamp
- Indicator for Relay output status
- Can Be controlled various appliances & other Equipment With Large current.
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
- The module is compliant with international safety standards, control and load areas isolation trenches;
1 Pole Industrial Relay PCB Relays, Model Name/Number: GU-SS-112DFS, Voltage: 12VDC
12V 10A PCB Mount Sugar Cube Relay – SPDT
Applications:-
- Domestic control and switching
- Car control switching box
- HVAC
- Home Automation and Security system
- Motor Control System etc.
- Type: SPDT
- Coil Voltage Rating: 12V
- Current: 10A
- Contact capacity:
- Pin counts: 5
- Mounting Type: Through-hole
- Length: 18.5mm
- Width: 15mm
- Height: 15mm
- Weight: 10gm
12V Active Buzzer: Premium Audio Alert Solution for Electronics Projects – Loud, Clear Sound, Easy Installation – Ideal for Alarms, Arduino, Robotics, DIY Projects & More!
63D-12-1CE RELAY 12V 30A OEN
DIODE RHR15120
DIODE RHR30120FSC
DIODE RHRP8120
ESP Prog – CP2102 Based ESP32
- Size: 50mmx30mm
- USB-C Type Interface: you can connect a USB in any direction. Use USB-A to USB-C Cable.
- LEDs for Power, RX, TX
- Switch for Reset and Boot
- Both 3.3V and 5V are available on the O/P connector
- All signals on a standard 2.54mm Pitch Header (Header will come along with the board (unsoldered))
- USB-C Type Interface: A USB can be connected in any direction. Use a USB-A to USB-C cable.
- LEDs for Power, RX, TX
- Switch for Reset and Boot
- Both 3.3V and 5V are available on the O/P connector
- All signals on a standard 2.54mm Pitch Header (Header will come along with the board (unsoldered))
- Compact size: 50mmx30mm
- 3.3V DC (100mA Max.)
- TXD
- RXD
- GND
- Reset/RTS
- Boot/DTR
- GND
- 5V DC (500mA Max.)
ESP32 Capacitive Touch Sensor Pins with Arduino IDEDS
ESP32 is designed for mobile, wearable electronics, and Internet-of-Things (IoT) applications. It features all the
state-of-the-art characteristics of low-power chips, including fine-grained clock gating, multiple power modes,
and dynamic power scaling. For instance, in a low-power IoT sensor hub application scenario, ESP32 is woken
up periodically only when a specified condition is detected. Low-duty cycle is used to minimize the amount of
energy that the chip expends. The output of the power amplifier is also adjustable, thus contributing to an
optimal trade-off between communication range, data rate and power consumption.
ESP32-CAM WiFi Bluetooth Camera Module Development Board ESP32 With Camera Module OV2640 2MP
Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC moduleLow-power dual-core 32-bit CPU for application processorsUp to 240MHz, up to 600 DMIPSBuilt-in 520 KB SRAM, external 4M PSRAMSupports interfaces such as UART/SPI/I2C/PWM/ADC/DACSupport for images WiFI uploadSupport TF cardSupport multiple sleep modesEmbedded Lwip and FreeRTOSSupport STA/AP/STA+AP working mode
